Video conference terminal web interface

Материал из База знаний VINTEO
Версия от 13:19, 17 сентября 2020; Alina (обсуждение | вклад)
(разн.) ← Предыдущая | Текущая версия (разн.) | Следующая → (разн.)

This section describes the process of setting up special software of a video conferencing terminal to connect to a VCS.

Access to the web interface is default enabled. To disable web access uncheck the box in the terminal settings:

Menu - System settings - Access - Web access.

Getting started with the application

To enter the functional menu you need:

  • launch a web browser;
  • enter the IP address of the video terminal in the address bar. The login page will open.
  • choose interface language;
  • check it out you have selected the Sign in button.
  • enter the account name to the Enter your login string. Default is admin.
  • enter your password to the string below. Default is 123.

Click the Submit button. The main window of the terminal will open.

Terminal1

To finish working with the interface close the web browser or click the Logout button in the lower left part of the screen.

Sidebar

Sidebar allows you to go to main web interface pages such as Terminal, Contacts, Reports, System. If you click on the Vinteo logo or shrink the window, the side menu will hide. At the bottom of the menu, two options are available: log out of the account and set it up to change the password.

Terminal 3.1.jpg

Terminal

Terminal page displays the image from the connected camera, the main indicators of the use of system resources, registration on the servers. You can call an account by number, view current calls, call history, dial a player, download video or video stream from an IP camera.

Two sliders are located below the video conferencing screen. They allow you to control the speaker and microphone volume. The camera controls are located at the bottom of the page. They allow you to remotely change the camera angle, its position in the horizontal and vertical planes, enlarge or reduce the image.

Terminal4

Calling an account manually

  • Choose the Manual dial way of calling the account.
  • Choose one of connect protocols: SIP, H.323, Local or Auto.
  • Enter the account number.
  • Choose the video stream resolution.
  • Choose the data baud rate.
  • Choose the frame rate.
  • Click Call button.
Terminal 5

Calling the account from the address book

  • Choose the account.
  • Choose the video stream resolution.
  • Choose the data baud rate.
  • Choose the frame rate.
  • Click Call button.
Terminal6

To call an account from the call history, go to the History tab and click on the button with the phone image.

Terminal7

Contacts

Contacts page is the local address book of the terminal which allows you to add new accounts.

Terminal8

It is possible to search the address book by entering the account's number or part of his name. Added the ability to increase the number of displayed strings on the page.

Terminal9

To create a new contact click the New contact button. Then the form for creating a new address book contact will open. In the form for adding a contact you need enter:

  • the contact name;
  • connection type. SIP, H.323 and Auto allowed;
  • the number;
  • selected contact;

click the Add button.

Terminal10

If you want to import contacts click the Import contacts button. Then choose the file you need to import and click the Import button. If you want to export contacts click the Export contacts button.

If there are several Vinteo video terminals in the contact book within one video conferencing server, then they are assigned the presence status. Presence statuses values:

  • Grey color means default status;
  • Yellow color means that the terminal is on but in call mode;
  • Red color means the terminal is on, but do not disturb mode is activated;
  • Green color means that the terminal is turned on and available for calls.

Logs

The Logs page is located on the functional panel on the left in the list of the Reports section. The following information is displayed on the Logs page:

  • report on each conference;
  • conference parameters;
  • used codecs;
  • parameters of participants;
  • other technical information about conference.
Terminal11

To view reports for a certain period you need:

  • specify a period from to in the filter strings;
  • click on the Search button.
Terminal12

You can view the logs in a browser window or download them. Use the button with the sheet image to view logs. Use the button with the arrow to download logs.

Terminal13

Reports page

The Reports page contains information about the technical state of the system, the time of the system reboot, reports on system errors, failures and other data.

Terminal14

To view reports for a certain period you need:

  • specify a period from to in the filter strings;
  • click on the Search button.

You can view the logs in a browser window or download them. Use the button with the sheet image to view logs. Use the button with the arrow to download logs.

Errors item on the functional panel

When you click to the Errors item of the list of the functional panel, the data file is exported. You need to send this file to Vinteo at the request of the technical support staff.

Status page

Status page allows you to view the main information about the terminal such as:

  • volume, free space and space occupied by videos on the hard drive;
  • system time;
  • terminal uptime;
  • current firmware version.
Terminal15

Videos page

On the "Videos" page, videos are added in the following formats: .mp4, .mov, .m4v, .mkv, .flv, .wmv, .avi to display them as an additional stream in the conference.
The size of uploaded videos should not exceed 100MB.

Terminal16

To add a video, you need to click in the upper right corner of the screen, then fill in the Title bar and Description field and select the file. Click the Add button after this button becomes active.

Terminal17

You can change the display style of files: a list or a grid. To delete a video click on the button with the image of the basket. In order to edit the previously uploaded video click on the button with the image of a pencil.

The main settings of the terminal

Main tab

On the main settings tab you can change:

  • firewall settings to deny access to SIP and H.323 ports from the local network;
  • H.323 parameters signaling port, RTP port range, enabling authorization by login / password;
  • SIP, STUN parameters, ToS signaling port and STUN port;
  • time and interface settings, language is default.
Terminal17

Firewall parameters work as an white list access.

If the list is empty access allowed from all networks visible to the terminal. If there is a single address or subnet address the access will be allowed only from addresses of this subnet.
Terminal18

Changing the signaling ports for H.323 and SIP requires the same values ​​to be configured on other devices.

Network interface settings

Network interface settings tab allows you to configure the receiving IP address for network interface (automatic mode / manual input). In automatic mode from a DHCP server.

To configure IP address in manual you need to fill follow fields:

  • IP
  • Network mask
  • Gateway
  • DNS
  • MTU

After that you need to click the Save button. You can configure it with two network interfaces.

Terminal19

Routs

The Routes tab browses automatically determined routes and assigns additional routes.

Terminal20

If you want to determine a new route click the Add route button. In the modal window specify:

  • destination address;
  • mask and gateway through which the destination address is available.

Choose the interface for connection to the gateway. Click the Add button.

Terminal21

The interface which you add displayed in the Assigned routes list. To delete the route click the trash image button.

NAT

The NAT tab allows you to configure the device if the device is located behind NAT. To do it specify the external IP address of the upstream device, local networks, assign the port range for the RTP protocol.

Terminal22

Enter the external address of the network device in the External IP field. Enter all subnet addresses that do not require external IP substitution in the Local networks field.

It is necessary to forward the SIP, H.323 ports and the RTP port range in the NAT configuration on the network device.

Incoming

The maximum allowable number of digits of the number is indicated incoming calls from which are blocked and IPs are automatically added to the black list.

It is possible to activate the black list which will block all traffic from addresses which are added in the black list.

  • Click the Add button.
  • Enter IP address.
  • Click the Save button.
Terminal23

Codecs

Codecs is the tab with lists of audio and video codecs supported by the account's device. The list on the left contains codecs which are available for use. On the right - the selected codecs for connection.

  • If the field is empty, the default codecs in the database are used.
  • If you have selected any codecs they will be applied. For example, if you have selected only audio codecs then the video stream will not be processed.
Be careful when choosing codecs. If you want to use the default codecs clear the field on the right.
Terminal24

Terminal

In the Terminal tab you can change the information about the terminal such as:

  • the name of the kit;
  • location;
  • default protocol;
  • resolution;
  • bandwidth;
  • FPS (frame frequency);
  • bandwidth mode;
  • maximum call duration;
  • monitors and their resolutions;
  • time to standby;
  • cameras and their resolutions;
  • possibility of choice of cameras roles;
  • turning on/off the auto answer;
  • auto answer time;
  • turning off the microphone when auto answer;
  • playback device;
  • recorder device;
  • enable echo cancellation;
  • ringtone turning on/off;
  • sound check button;
  • Do not disturb mode;
  • enable SIP and H.323.
Terminal25

SIP registration

Registration SIP tab serves for the connection parameters setting to the SIP server’s IP address, authorization and using codecs.

To register the terminal using only the terminal IP address. If the settings provide for authorization, you must enter the username and password in the appropriate strings. You can choose TCP protocol or UDP protocol the call will be carried out.

It is recommended to use the next codecs settings and data transfer protocol.

Terminal26

H.323 registration

Registration H.323 tab serves for the connection parameters setting to the H.323 server’s IP address, authorization and using codecs.

Terminal27
As with SIP settings to register the terminal using only the terminal IP address. If the settings provide for authorization, you must enter the username and password in the appropriate strings.

It is recommended to use the next codecs settings.

Terminal28

Screensaver

Images that are downloaded will be shown on the screen in the Screensaver tab while the terminal is in standby mode. In this tab you can configure the frequency of displaying the screensaver and enabling / disabling this function.

Terminal29

To add the screensaver you need to click the Upload button. Choose the needed image and click the Upload button.

Terminal30

In this tab you can configure the frequency of displaying the screensaver and enabling / disabling this function.

Diagnostics

The Diagnostics tab considers common utilities for diagnostic problems about local network connection. Utilities are giving below:

  • Ping;
  • Traceroute;
  • Tcpdump;
  • Logs utility logs a call for diagnostic problems when making a call.
Terminal31

Power management

2 remaining tabs allow you to reboot and shutdown the power of the terminal.

Licenses

The special software of the video conference terminal is distributed under the license. On the Licenses page you can install the license of the terminal, view previously installed licenses and quantity of licenses available for a new participants connection.

One HD type license allows you to connect participants with different resolutions. One HD license allows you to connect participants at different resolutions. It will be shown below how licenses can be spent.

SD (576p / 30) audio and video connection will take 0.5HD license.

  • The connection more than 576p / 30 and less than or equal to 720p / 30 will take a 1HD license.

подключение больше 720р/30 и меньше или равно 1080р/30 займет 2,5HD лицензии;

  • The connection more than 720p/30 and less or equal 1080p/30 will take 2,5HD licenses.
The participant connection with video stream more than 30 frames per second will take 2x more HD licenses than this requires for connection with the same resolution and frequency before 30 frames per second. 
Terminal31

License installation

To install the license you need:

  • request the quantity of license which you need;
  • provide the unique installation ID;
  • enter the code in the Activation code field;
  • click the Activate button.

In the Current license block is displayed the quantity HD and FullHD licenses.

Update

This page allows you to install firmware update. To install the file you need:

  • click the Choose file button;
  • choose the update file;
  • click the Upload button.
Before updating switch off from the terminal all USB flash drivers.
Update