Checking network bandwidth using iPerf3: различия между версиями

Материал из База знаний VINTEO
Строка 18: Строка 18:
  
 
2. unpack the files from the archive into a folder convenient for you.
 
2. unpack the files from the archive into a folder convenient for you.
 +
 +
3. open the command line (Win+R keys) and enter cmd then press Enter in the window that appears (in all versions of Windows); then go to the folder with the unpacked iPerf3 files.
 +
 +
= Testing the channel from client to server =
 +
 +
To check the level of packet loss from the client to the server you need to run the test with the command:
 +
 +
iperf3 -c <server_ip> -u -w 1m -t 10 -l 1100 -b 1M
 +
 +
-с <server_ip> — key to run in client mode with specifying the server address;
 +
 +
-u — it is necessary to specify that the UDP protocol is used;
 +
 +
-w 1m — you must specify the iPerf3 buffer size;
 +
 +
-t 10 — you must specify the test time of 10 seconds;
 +
 +
-l 1100 — specify the packet length; set it to at least 28 bytes less than the MTU to prevent fragmentation. 1100 bytes is the average RTP packet size so we recommend this value;
 +
 +
-b 1M – indicate the required bitrate for the test (1 Mbit/sec). You can use modifiers: K – kilobyte, M – megabyte, G – gigabyte.
 +
 +
Information about other keys and parameters of the utility can be found here: https://iperf.fr/iperf-doc.php#3doc
 +
 +
The figure below shows the operation of the iPerf utility.

Версия 16:55, 1 октября 2024

iPerf3 is the console utility. You can measure with its help the maximum network throughput between the videoconferencing server and the client or conduct load testing of the communication channel to determine the level of losses. Before starting testing you need to run iPerf on the server. Special patch was developed for this.

Installing the patch on the server

1. in the "System" server section go to the "Upgrade" subsection;

2. go to the “Settings” tab and by clicking the file selection button specify the path to the file with the patch. To receive the patch you must contact Vinteo technical support;

3. click the "Upload" button. the message will appear: “Attention! The configuration downloaded successfully and installed. The system will start within 5 minutes”;

Upgrade

4. you need to wait until the settings are applied. To do this go to the "System" section in the "Status" subsection and wait until in the "Server uptime" item the system updates the work status from "System down" to "System uptime";

5. You can begin installing the utility on the client PC.

Installing and running the utility

1. download and install the iPerf3 utility from the official website: https://iperf.fr/iperf-download.php/

2. unpack the files from the archive into a folder convenient for you.

3. open the command line (Win+R keys) and enter cmd then press Enter in the window that appears (in all versions of Windows); then go to the folder with the unpacked iPerf3 files.

Testing the channel from client to server

To check the level of packet loss from the client to the server you need to run the test with the command:

iperf3 -c <server_ip> -u -w 1m -t 10 -l 1100 -b 1M

-с <server_ip> — key to run in client mode with specifying the server address;

-u — it is necessary to specify that the UDP protocol is used;

-w 1m — you must specify the iPerf3 buffer size;

-t 10 — you must specify the test time of 10 seconds;

-l 1100 — specify the packet length; set it to at least 28 bytes less than the MTU to prevent fragmentation. 1100 bytes is the average RTP packet size so we recommend this value;

-b 1M – indicate the required bitrate for the test (1 Mbit/sec). You can use modifiers: K – kilobyte, M – megabyte, G – gigabyte.

Information about other keys and parameters of the utility can be found here: https://iperf.fr/iperf-doc.php#3doc

The figure below shows the operation of the iPerf utility.